RefrigeratorsWe fix GE, GE Profile and Café fridges that stop cooling or leak inside.
dEDefrost problem
The defrost system hasn't worked properly in the last 24 hours.
What to try
Keep the doors closed and check they seal. Unplug it for one to two minutes to reset.
When to call
If dE returns, the defrost system needs testing.
1-Year Parts & Labour Warranty
Diagnostic regularly $129, now $99
GE Appliance Repair in Vaughan
GE, GE Profile and Café fridge, stove, washer, dryer and dishwasher repair in Vaughan. Diagnostic regularly $129, now $99, and always waived when Aria does the repair.
- Service Area
- Vaughan
- York Region
- Hours
- Mon–Sun 8 AM–10 PM
- Same-Day Service Available
- Diagnostic
- $99 (reg. $129)
- Waived when we do the repair
- Google Rating
- 5.0 out of 5
- On Google
- Coverage
- 1-Year Parts & Labour Warranty
- An industry-high warranty.
- Call or Book
- 1-888-642-0352
- Book Online
Every GE in your home, one local team
GE appliances are sold in Canada under GE, GE Profile and Café, and a lot of Vaughan kitchens have at least one of them. GE stoves and dishwashers show short codes like F3 or C1 when something goes wrong, and many GE dryers light up a Check Vent alert. Write down what you see, because it points us to the right system before we arrive.
We repair GE, GE Profile and Café fridges, stoves, wall ovens, cooktops, dishwashers, washers, dryers, over-the-range microwaves and range hoods. Diagnostic regularly $129, now $99, and always waived when Aria does the repair. You get the price before any work starts, and completed repairs include our 1-Year Parts & Labour Warranty. Call 1-888-642-0352, Mon–Sun 8 AM–10 PM.
RefrigeratorsWe fix GE, GE Profile and Café fridges that stop cooling or leak inside.
Stoves & ovensWe repair GE gas and electric stoves that won't light or heat.
WashersWe fix GE top-load and front-load washers that won't spin or drain.
DryersWe fix GE dryers that stop heating, run long or show Check Vent.
DishwashersWe fix GE dishwashers that show a C code, won't drain or leave dishes dirty.
MicrowavesWe repair GE over-the-range microwaves with fans, lights or heating that quit.
Range hoodsWe repair GE range hoods with fans, lights or controls that quit.
GE Fridge Problems We Fix
We repair GE, GE Profile and Café fridges, including French-door models, starting with the simple causes.
Water Under the Crisper Drawers
- Likely cause
- Usually a frozen or blocked defrost drain, so melt water from the freezer coil overflows into the fridge section.
- Try this first
- Take out the crisper drawers, dry the bottom and check for ice at the back. Make sure the fridge is level side to side and tilts slightly back, so the doors swing closed.
- When to call Aria
- If water keeps coming back after a few days, book a visit. We clear the drain and check the defrost heater that keeps it from freezing again.
Fridge Warm, Freezer Still Cold
- Likely cause
- The evaporator fan, or frost on the coil from a defrost fault that blocks cold air to the fridge side.
- Try this first
- Make sure nothing is pressed against the vents and the doors close all the way. A fridge thermometer on a middle shelf tells you the real temperature.
- When to call Aria
- If it stays above 4 °C after a day, book a visit.
Ice Maker Not Making Ice
- Likely cause
- A frozen fill tube, a failed water inlet valve, or an ice maker that has stopped cycling.
- Try this first
- Check the ice maker switch or the feeler arm is on, the water filter isn't overdue, and the water supply valve behind the fridge is open.
- When to call Aria
- If ice still won't come after a day, book a visit.
Fridge Running Loud or Clicking
- Likely cause
- A noisy evaporator or condenser fan, or a compressor start part that clicks on and off.
- Try this first
- Pull the fridge out a little and check nothing is touching the back, and that the fridge is level. Vacuum the condenser coils if your model has them at the bottom.
- When to call Aria
- If the noise is new and it's getting warmer, book a visit. A clicking start part is a common, quick repair.
Good to know
Keep the doors closed while you wait for us, and put a towel under the crispers if water is collecting.
Most fridge repairs we do land around $120–$550, depending on the part. You get the exact price before any work starts.
RelatedRefrigerator repair · Fridge not cooling guide · Fridge repair cost
GE Stove and Oven Problems We Fix
We repair GE, GE Profile and Café gas and electric stoves, wall ovens and cooktops, including convection models.
Gas Burner Clicks but Won't Light
- Likely cause
- Usually a wet or misaligned burner cap, or a weak igniter or spark module.
- Try this first
- Once the cooktop is cool, dry the burner cap and base and seat the cap flat. Spills often stop a burner lighting for a while.
- When to call Aria
- If it still won't light, or keeps clicking after it lights, book a visit. If you smell gas, leave it off and call your gas utility first.
Oven Not Heating
- Likely cause
- A failed bake element, a weak gas oven igniter, or the oven temperature sensor.
- Try this first
- Check the breaker, make sure a delay start or Sabbath mode isn't on, and try Broil to see if the top element or burner heats.
- When to call Aria
- If Bake stays cold, book a visit. We test the element, igniter and sensor before replacing anything.
F3 or F9 Code on the Display
- Likely cause
- On many models, F3 or F4 points to the oven sensor and F9 to the door lock circuit. F2 means the oven ran too hot.
- Try this first
- Turn the stove off at the breaker for one minute and try again. Don't use the oven while an F2 code is showing.
- When to call Aria
- If the code comes back, write it down and book a visit.
Door Locked After Self-Clean
- Likely cause
- The oven stays locked until it cools. If it won't unlock once cool, often the door lock motor or switch has failed.
- Try this first
- Let the oven cool fully, then press Clear/Off. If LOC shows, the controls are locked. On many models you hold the Lock Controls pad for 3 seconds to unlock.
- When to call Aria
- If the door still won't unlock once cool, book a visit. Please don't force the door.
Good to know
GE wall ovens and cooktops get the same approach: we test the element, igniter, sensor and controls before replacing anything.
Most stove and oven repairs we do land around $130–$350, depending on the part. You get the exact price before any work starts.
RelatedStove and oven repair · Oven not heating guide · Oven repair cost
GE Washer Problems We Fix
We repair GE and GE Profile top-load and front-load washers, including agitator and impeller models.
Not Spinning, Clothes Soaking Wet
- Likely cause
- An unbalanced load, a lid or door lock that isn't engaging, a blocked drain, or a worn shifter or drive part.
- Try this first
- Spread the load out evenly and run a Drain & Spin cycle. On top-loaders, make sure the lid is fully closed.
- When to call Aria
- If it still won't spin, book a visit. Tell us if you hear the motor hum or nothing at all.
Not Draining
- Likely cause
- A sock or small item in the pump, a kinked drain hose, or a drain pump that has failed.
- Try this first
- Check the drain hose isn't kinked or pushed too far into the standpipe. On front-loaders, clean the pump filter behind the small door at the bottom front, with towels down first.
- When to call Aria
- If water still won't drain, the pump needs testing.
Washer Leaking
- Likely cause
- A loose fill hose, a split drain hose, too much suds, or a tub seal or pump leak.
- Try this first
- Check both fill hoses are tight at the back and use HE detergent, a little less of it.
- When to call Aria
- If water still shows up after a normal load, book a visit. Tell us where the puddle starts.
Lid or Door Won't Lock
- Likely cause
- Something caught in the lid or door, or a worn lid lock or door lock.
- Try this first
- Close the lid or door firmly, check nothing is in the way, and unplug the washer for one minute before restarting.
- When to call Aria
- A worn lock is a common repair. If the lights keep flashing, book a visit.
Good to know
On top-loaders, washing one bulky item like a comforter on its own can stop the spin. Add a couple of towels to balance it.
Most washer repairs we do land around $150–$350, depending on the part. You get the exact price before any work starts.
RelatedWasher repair
GE Dryer Problems We Fix
We repair GE and GE Profile electric and gas dryers, including stacked and laundry-centre units.
Dryer Not Heating
- Likely cause
- On electric dryers, often a heating element or thermal fuse. On gas dryers, an igniter or gas valve coils. A blown thermal fuse usually means the vent was blocked.
- Try this first
- Check both breakers for an electric dryer, since one can trip and leave the drum turning with no heat. On gas dryers, check the gas valve behind the dryer is open.
- When to call Aria
- We test and replace the failed part, and check the vent so it doesn't happen again.
Check Vent Light or Long Dry Times
- Likely cause
- Lint building up in the vent duct, or a crushed duct behind the dryer. GE's Check Vent alert is a warning about airflow, not a dryer fault.
- Try this first
- Clean the lint filter, then check the duct isn't crushed and the outside flap opens when the dryer runs.
- When to call Aria
- If the vent is clear and loads still take more than one cycle, book a visit.
Squealing or Thumping
- Likely cause
- Worn drum rollers, a worn idler pulley or drum glides, or a loose belt.
- Try this first
- Check for a coin or zipper caught between the drum and the front.
- When to call Aria
- If the noise stays, stop using it and book a visit. These parts are worth replacing before they damage the drum.
Dryer Won't Start
- Likely cause
- The door switch, a thermal fuse, or the start switch or control.
- Try this first
- Make sure the door is shut firmly and the breaker is on. Check whether a control lock is on, since many GE dryers have one.
- When to call Aria
- If it still won't start, book a visit.
Good to know
Short, straight 4-inch metal duct helps any dryer dry faster and keeps the Check Vent alert away.
Most dryer repairs we do land around $130–$320, depending on the part. You get the exact price before any work starts.
RelatedDryer taking too long · Dryer repair
GE Dishwasher Problems We Fix
We repair GE, GE Profile and Café built-in dishwashers, including models with a hard food disposer or a manual filter.
Dishes Still Dirty
- Likely cause
- A dirty filter, blocked spray arms, cold water at the start, or a weak wash pump.
- Try this first
- Clean the filter if your model has a removable one, check the spray arms spin freely, and run the kitchen tap until it's hot before starting.
- When to call Aria
- If dishes still come out gritty, book a visit. Code C6 means the water is too cold, at least 49 °C (120 °F) is needed.
Not Draining (C1 or C3)
- Likely cause
- A blocked air gap, a kinked drain hose, a new disposal's knockout plug, or a drain pump that has failed.
- Try this first
- Clean the filter, check the drain hose under the sink, clean the air gap on the counter if you have one, and run the disposal before you start.
- When to call Aria
- If water still sits in the bottom, the pump needs testing.
Leaking or Water Under the Door
- Likely cause
- A worn door gasket, the wrong detergent, or a stuck float. Some models show C4 or LEAK DETECTED.
- Try this first
- Use only dishwasher detergent, never dish soap. Check the door closes evenly, and gently tap the float cover inside the tub to free it.
- When to call Aria
- Switch it off and book a visit if water keeps appearing.
Detergent Not Dissolving (C8)
- Likely cause
- Something blocking the detergent cup door, or a dispenser that has failed.
- Try this first
- Check a tall pan or utensil isn't blocking the detergent cup, and that the door closes fully.
- When to call Aria
- If the cup still won't open, book a visit.
Good to know
Codes vary by model. Write down the exact code from the display, since it helps us bring the right part.
Most dishwasher repairs we do land around $130–$340, depending on the part. You get the exact price before any work starts.
GE Microwave and Range Hood Problems We Fix
We repair GE, GE Profile and Café over-the-range microwaves and GE range hoods.
Vent Fan or Light Not Working
- Likely cause
- A failed fan motor, a blown bulb or LED, a thermal switch, or the control board.
- Try this first
- Clean or replace the grease filters under the microwave or hood, and try the fan on every speed. Replace the cooktop light bulb if it's a bulb type.
- When to call Aria
- If the fan stays silent or the light won't come on with a new bulb, book a visit.
Microwave Runs but Doesn't Heat
- Likely cause
- A failed high-voltage diode, capacitor, magnetron or door switch.
- Try this first
- Make sure the door closes firmly and heat a cup of water for one minute. If the light and turntable work but the water stays cold, stop using it.
- When to call Aria
- Microwaves hold a charge even when unplugged, so please don't open the cover. Book a visit.
Turntable Not Turning
- Likely cause
- The turntable isn't seated on its coupler, or the turntable motor has failed.
- Try this first
- Lift out the glass tray and roller ring, clean them and seat the tray back onto the centre coupler. Check the turntable isn't switched off.
- When to call Aria
- If it still won't turn, the motor needs replacing.
Hood Not Clearing Smoke
- Likely cause
- Clogged grease filters, a stuck damper, or an old charcoal filter on a recirculating setup.
- Try this first
- Soak the metal grease filters in hot soapy water, and replace the charcoal filter if your hood recirculates.
- When to call Aria
- If the fan sounds weak with clean filters, book a visit to check the motor and damper.
Good to know
Microwaves can hold a charge after unplugging, so please don't open the housing yourself. We test them safely.
RelatedMicrowave repair · Range hood repair
GE Error Codes by Appliance
Codes vary by model, so treat this as a guide for many models, not every one.
GE Fridge Codes
See fridge problemsFFFreezer is getting too warm
Check frozen food for thawing.
What to try
Make sure the freezer door closes fully and the vents aren't blocked.
When to call
If it keeps warming up, book a visit.
CCFridge temperature is off
What to try
Check the temperature setting and that the doors close fully.
When to call
If the setting is right and it stays warm, book a visit.
CICheck the ice maker
What to try
Make sure the ice maker is on and nothing is jammed in the bin.
When to call
If it still won't make ice, the ice maker needs testing.
PFPower was interrupted
What to try
Check the food is still cold.
When to call
If it keeps showing without a power outage, book a visit.
GE Stove and Oven Codes
See stove and oven problemsF2Oven running too hot
Shown as F20 on some models.
What to try
Turn it off at the breaker for one minute. Don't use the oven while F2 shows.
When to call
If it comes back, the sensor or control needs testing.
F3 / F4Oven temperature sensor problem
What to try
Reset the breaker for one minute and try again.
When to call
If it returns, we test the sensor and wiring.
F1 / F7Keypad problem
Shown as F0 or F6 on some models.
What to try
Reset the breaker for one minute.
When to call
If it comes back, the keypad usually needs replacing.
F9Door lock circuit problem
Often after a self-clean.
What to try
Let the oven cool, then reset the breaker for one minute.
When to call
If the door won't unlock once cool, book a visit.
LOCControls are locked
A setting, not a fault.
What to try
On many models, hold the Lock Controls pad for 3 seconds.
When to call
If the controls won't unlock, book a check.
Bad LineWired incorrectly
Usually right after installation.
What to try
Don't use the stove.
When to call
Call your installer or an electrician to fix the wiring.
GE Washer Codes
See washer problemsH2O SUPPLYWater not coming in
Also shown as IE, or the Wash and Rinse lights blinking. Top-load models from 2017 on.
What to try
Open both taps fully, then wait 4 minutes. Unplugging restarts the wait.
When to call
If the taps are open, the inlet valve may have failed.
dELid is open
Top-load models.
What to try
Close the lid and press Start/Pause.
When to call
If the lid is closed and dE stays, the lid switch needs testing.
UELoad is unbalanced
What to try
Spread the load out evenly and check the washer is level.
When to call
If it shows with even loads, the suspension needs checking.
LidOpen the lid first
Shown after 3 cycles started without opening the lid.
What to try
Open and close the lid, then start a new cycle.
When to call
If it keeps showing, book a visit.
FEWater level too high
A safety alert.
When to call
Turn off the water and the power to the washer, then call us.
GE Dryer Codes
See dryer problemsCheck VentRestricted airflow
A warning about the vent, not a dryer fault. A blocked vent is a fire risk.
What to try
Clean the lint filter, the duct and the outside flap.
When to call
If the vent is clear and the alert stays on, book a visit.
LockControls are locked
A setting, not a fault. The lock icon is on.
What to try
On many models, hold Extended Tumble and − (minus) for 3 seconds. On others, hold Light for 3 seconds.
When to call
If it won't unlock, book a check.
Open DoorDoor signal not detected
Newer models (such as the GTD69 series) scroll this after five cycles without the door being opened.
What to try
Open the door, then close it firmly.
When to call
If it keeps showing, the door switch or its wiring needs testing.
001 / 003Inlet temperature sensor problem
Service-mode fault code on newer GE dryers (such as the GTD69 series). A technician reads it from the fault log. 001 means shorted, 003 open.
What to try
Clean the lint screen and check the vent is clear.
When to call
If it dries poorly or runs hot, book a visit so we can read the fault log.
002 / 004Outlet temperature sensor problem
Service-mode fault code on newer GE dryers (such as the GTD69 series). A technician reads it from the fault log. 002 means shorted, 004 open.
What to try
Clean the lint screen and check the vent is clear.
When to call
If it dries poorly or runs hot, book a visit so we can read the fault log.
006Stuck button
Service-mode fault code on newer GE dryers (such as the GTD69 series). A technician reads it from the fault log. Logged when a button is held for a minute.
What to try
Make sure nothing is pressing on the control panel.
When to call
If buttons stop responding, the controls need a technician.
007Wired incorrectly
Service-mode fault code on newer GE dryers (such as the GTD69 series). A technician reads it from the fault log. Usually right after installation.
What to try
Stop using the dryer until the wiring is checked.
When to call
Call us or your installer to correct the wiring.
GE Dishwasher Codes
See dishwasher problemsC1Taking too long to drain
What to try
Clean the air gap, check the drain hose and the disposal knockout plug.
When to call
If it still won't drain, the pump needs testing.
C3Not draining
What to try
Turn off the breaker for 30 seconds, then clean the filter and check the drain hose.
When to call
If water still sits in the bottom, the pump needs testing.
C4Float stuck or water in the base
What to try
Gently tap the float cover in the tub and check the sump for debris.
When to call
If it comes back, switch it off and book a check.
C6Water too cold
At least 49 °C (120 °F) is needed.
What to try
Run the kitchen tap until it's hot before starting.
When to call
If the water is hot and C6 stays, the heater or sensor needs testing.
C8Detergent cup blocked
What to try
Move any dish or utensil blocking the cup, close the door and wait 30 seconds.
When to call
If the cup still won't open, book a visit.
H2OLow water
What to try
Check the water supply hose under the sink isn't kinked.
When to call
If the hose is fine, the inlet valve needs testing.
LEAK DETECTEDPossible leak
On models with leak detection, the cycle is cancelled.
When to call
Turn off the water to it and book a check.
GE Microwave Codes
See microwave problemsF1Overheated or open thermal sensor
Often from too much heat inside.
What to try
Let it cool, then turn off the breaker for 30 seconds.
When to call
If it returns, the sensor needs testing.
F2Thermal sensor problem
What to try
Turn off the breaker for 30 seconds.
When to call
If it returns, the sensor needs testing.
F3Keypad problem
What to try
Turn off the breaker for 30 seconds.
When to call
If it comes back, the keypad needs replacing.
F4 / F5Humidity sensor problem
What to try
Turn off the breaker for 30 seconds.
When to call
If it returns, the sensor needs testing.
PF / 888Power was interrupted
Also shown after installation.
What to try
Press Cancel/Off or Clear/Off, then set the clock.
When to call
If it keeps showing without a power outage, book a visit.
Code still showing after the quick checks? Tell us the code when you book.
Typical GE Repairs
Typical GE repairs we see, and what usually fixes them. See our recent jobs on Our Work.
Typical GE repair
GE Fridge: Water Under the Crispers
A frozen defrost drain sends melt water into the fridge section. We clear the drain and test the defrost heater, so it doesn't freeze up again.
Fridge repairTypical GE repair
GE Gas Stove: Burner Won't Light
Usually a burner cap out of place, or a worn igniter or spark module. We test the spark system and replace only the part that has failed.
Stove repairTypical GE repair
GE Dishwasher: C1 or C3 Code
Most drain codes come down to a blocked air gap, hose or filter, and sometimes the drain pump. We clear the blockage and test the pump before replacing anything.
Dishwasher repairGE Repair Pricing
Current offers on diagnostics and installation. You always get the price before work begins.
Diagnostic regularly $129, now $99
$99
Your technician diagnoses your GE and gives you the price before any work begins. Diagnostic regularly $129, now $99, and always waived when Aria does the repair.
Installation From $129
From$129
A new GE, GE Profile or Café appliance installed from $129. Pricing depends on the appliance and the existing connections. See installation.
Payment
- Card
- Debit
- Cash
- PayPal
- Apple Pay
* Offers subject to change; price confirmed before work begins.
What Happens at the Visit
Book online or call us. We’ll confirm your appointment, diagnose the problem, and provide the repair price before any work begins.
- Step 01
Book Your Appointment
Call or book online and tell us which appliance needs service and what problem you’re experiencing.
- Step 02
We Diagnose the Problem
A technician inspects the appliance to find the cause of the problem.
- Step 03
You Approve the Repair
We explain the recommended repair and pricing before any work begins.
- Step 04
Repair & Testing
The approved repair is completed and the appliance is tested before we finish.
What to Tell Us When You Book
That helps us bring the right part and finish on the first visit more often.
The code
Exactly as shown, like F3 C1 Check Vent
The model number
- Fridges on the inside wall or ceiling of the fresh-food section
- Stoves behind the storage drawer or on the oven frame
What you've tried
Like cleaning a filter or power-cycling the unit.
When it happens
At the startMid-cycleAt the end
Repair or Replace Your GE?
A simple rule of thumb, then the factors that change it. More on this: repair or replace your appliance.
Repair cost as a share of a comparable new GE
Under about halfand the rest in good shape: repair it.
Over about half, or other problems building upIt's a bigger decision. We give you the price so you can weigh it up.
Age & condition
An older appliance with several problems is a different call from a reliable one with a single failure.
Type of failure
Most GE repairs we see are a single part: an igniter, a heating element, a defrost heater, a door lock, a drain pump or a fan.
The big-ticket parts
Compressor or sealed-system work on an older fridge, or a main control board on an older stove or washer.
The price, first
We give you the price first, so you can decide with real numbers.
On GE gas stoves, igniters and spark modules are usually worth fixing at almost any age. If replacing makes more sense, we also do installation from $129.
What Homeowners Say About Aria
Leave a Google ReviewReal reviews from Vaughan homeowners on Google.
Where We Work
GE repair in every part of Vaughan, including Woodbridge, Thornhill, Maple, Kleinburg and Concord. Not in Vaughan? Yes, we may still be able to help. Call 1-888-642-0352 to confirm. See recent jobs on Our Work.
Service areaVaughanVaughan, Ontario
- Woodbridge
- Maple
- Concord
- Kleinburg
- Thornhill
- Vellore Village
- Sonoma Heights
- Patterson
- Elder Mills
- Vaughan Metropolitan Centre
- Carrville
- Islington Woods
Call 1-888-642-0352Mon–Sun 8 AM–10 PM
Book OnlineGE is a trademark of its owner. Aria Appliance Repair is independent and not affiliated with GE.
What does F3 mean on my GE oven?
On many GE ovens, F3 or F4 points to the oven temperature sensor or its wiring. Turn the stove off at the breaker for one minute and try again. If the code comes back, we test the sensor and wiring and replace what has failed.
What do F2 and F9 mean on a GE oven?
On many models, F2 means the oven ran too hot, so don't use it while the code shows. F9 points to the door lock circuit, often after a self-clean. Let the oven cool, then reset the breaker for one minute. If either code returns, book a visit.
Why won't my GE oven door unlock after self-clean?
The door stays locked until the oven cools. Once cool, press Clear/Off. If LOC shows, the controls are locked, and on many models you hold Lock Controls for 3 seconds. If the door still won't unlock, the lock motor or switch has often failed. Please don't force the door.
Why won't my GE gas burner light?
Usually the burner cap is wet or sitting crooked, or the igniter is weak. Let the cooktop cool, dry the cap and base, and seat the cap flat. If it still clicks without lighting, we test the igniter and spark module. If you smell gas, leave it off and call your gas utility first.
Why is there water under the crispers in my GE fridge?
Usually the defrost drain at the back of the freezer has frozen or blocked, so melt water overflows into the fridge section. Dry it up and check the fridge is level. If water keeps coming back, we clear the drain and test the defrost heater so it doesn't freeze again.
What do C1 and C3 mean on a GE dishwasher?
On many models, C1 means the dishwasher took too long to pump out and C3 means it isn't draining. Clean the filter, check the drain hose and the air gap, and make sure a new disposal's knockout plug was removed. If water still sits in the bottom, the drain pump needs testing.
What does Check Vent mean on my GE dryer?
It means the dryer is sensing restricted airflow, usually lint in the duct or a crushed duct behind the dryer. It's a warning, not a dryer fault. Clean the lint filter, check the duct and the outside flap. If the vent run is long or hard to reach, a vent cleaning company is the right call.
Why is my GE washer not spinning?
Often the load is out of balance, the lid isn't locking, or the washer can't drain. Spread the load out and run a Drain & Spin cycle. If it still won't spin, book a visit. Tell us whether you hear the motor hum, since that helps us plan.
Do you repair GE Profile and Café appliances?
Yes. GE Profile and Café are both GE Appliances lines, and we repair their fridges, stoves, wall ovens, cooktops, dishwashers, washers, dryers and over-the-range microwaves the same way: test first, then give you the price before any work starts.
How much does GE repair cost?
Diagnostic regularly $129, now $99, and always waived when Aria does the repair. After testing, you get the exact repair price before any work starts. Installing a new GE appliance starts from $129. We accept cards, debit, cash, PayPal and Apple Pay, and completed repairs carry our 1-Year Parts & Labour Warranty.
Is it worth repairing a GE appliance?
Most GE repairs are a single part: an igniter, an element, a defrost heater, a door lock, a pump or a fan, and those are usually worth fixing. A simple rule: if the repair costs less than about half of a comparable new appliance, repair it. The bigger calls are sealed-system fridge work or a main control board. We price it first, so you decide.
How do I book GE repair near me?
Book online by choosing your appliance, a day and an arrival window, or call 1-888-642-0352, Mon–Sun 8 AM–10 PM. We serve all of Vaughan, including Woodbridge, Maple, Kleinburg, Concord and Thornhill. If you're outside Vaughan, call to confirm your address. Write down any code on the display first, because it helps us plan the visit.
Need Appliance Repair or Installation?
Tell us which appliance you need repaired or installed and we’ll help arrange your appointment.
- Same-Day Service Available
- 1-Year Parts & Labour Warranty
- Mon–Sun 8 AM–10 PM
