RefrigeratorsWe fix Whirlpool fridges that stop cooling, frost up or stop making ice.
POThe power was out
Shown after an outage if the freezer warmed up. Mostly French-door models with a display.
What to try
Check the food, then press the button under Confirm to clear it.
When to call
If it shows with no outage, book a visit.
1-Year Parts & Labour Warranty
Diagnostic regularly $129, now $99
Whirlpool Appliance Repair in Vaughan
Whirlpool washer, dryer, fridge and stove repair in Vaughan. Error codes, leaks, no heat. Diagnostic regularly $129, now $99, and always waived when Aria does the repair.
- Service Area
- Vaughan
- York Region
- Hours
- Mon–Sun 8 AM–10 PM
- Same-Day Service Available
- Diagnostic
- $99 (reg. $129)
- Waived when we do the repair
- Google Rating
- 5.0 out of 5
- On Google
- Coverage
- 1-Year Parts & Labour Warranty
- An industry-high warranty.
- Call or Book
- 1-888-642-0352
- Book Online
Every Whirlpool in your home, one local team
Whirlpool is in a lot of Vaughan kitchens and laundry rooms, often bought together as a full set. Newer Whirlpool washers, dryers, dishwashers and stoves show an F-and-E code like F9 E1 when something goes wrong. Write the code down, because it points us to the right system before we arrive.
We repair Whirlpool front-load and top-load washers, dryers, fridges, dishwashers, stoves, wall ovens, cooktops, over-the-range microwaves and range hoods. Diagnostic regularly $129, now $99, and always waived when Aria does the repair. You get the price before any work starts, and completed repairs include our 1-Year Parts & Labour Warranty. Call 1-888-642-0352, Mon–Sun 8 AM–10 PM.
RefrigeratorsWe fix Whirlpool fridges that stop cooling, frost up or stop making ice.
Stoves & ovensWe repair Whirlpool stoves, wall ovens and cooktops that won't heat evenly.
WashersWe fix Whirlpool front-load and top-load washers that leak or won't drain.
DryersWe fix Whirlpool dryers that run long, show Check Vent or stop heating.
DishwashersWe fix Whirlpool dishwashers that won't drain, leak or leave dishes dirty.
MicrowavesWe repair Whirlpool over-the-range microwaves, including low-profile models.
Range hoodsWe repair Whirlpool range hoods with fans, lights or controls that quit.
Whirlpool Fridge Problems We Fix
We repair Whirlpool fridges, including French-door models, and we rule out the simple causes before anything expensive.
Both Sections Warming Up
- Likely cause
- Dirty condenser coils, a condenser fan that has stopped, or the start parts or control that run the compressor.
- Try this first
- Check the fridge is plugged in, the breaker is on and the temperature wasn't turned up by accident. Keep the doors closed.
- When to call Aria
- We test the fans, coils and start parts first, and the sealed system last. If it's a compressor, you get the price plainly so you can compare it with a new fridge.
Fridge Warm, Freezer Still Cold
- Likely cause
- Usually the evaporator fan, or frost on the coil from a defrost fault that blocks cold air from reaching the fridge side.
- Try this first
- Make sure food isn't pushed against the vents at the back, and that both doors close all the way. A fridge thermometer on a middle shelf tells you the real temperature.
- When to call Aria
- If it's above 4 °C after a day and the freezer is still cold, book a visit. That pattern points us straight to the fan and defrost parts.
Ice Maker Not Making Ice
- Likely cause
- A frozen fill tube, a failed water inlet valve, or an ice maker that has stopped cycling.
- Try this first
- Check the ice maker is switched on and the arm or switch isn't in the off position. A water filter that's overdue can slow the water to a trickle, so replace it if it's past six months.
- When to call Aria
- If ice still won't come after a day with a fresh filter, book a visit.
Water on the Floor or Under the Crispers
- Likely cause
- A blocked defrost drain or a cracked or loose water line to the dispenser or ice maker.
- Try this first
- Wipe up the water, check the water filter is fully locked in, and look behind the bottom grille for a drip tray that's overflowing.
- When to call Aria
- If the water keeps coming back, book a visit. A blocked defrost drain usually needs the back panel off to clear properly.
Good to know
Keep the doors closed while you wait for us, and don't keep switching it off and on.
Most fridge repairs we do land around $120–$550, depending on the part. You get the exact price before any work starts.
RelatedRefrigerator repair · Fridge not cooling guide · Fridge repair cost
Whirlpool Stove and Oven Problems We Fix
We repair Whirlpool electric and gas stoves, wall ovens and cooktops, including air fry and steam clean models.
Oven Not Heating or Slow to Preheat
- Likely cause
- A failed bake or broil element, a weak gas igniter, or the oven temperature sensor. Many newer Whirlpool ovens hide the bake element under the oven floor, so you can't see it glow.
- Try this first
- Check the breaker, make sure a delay or timed cook isn't set, and try Broil to see if the top element heats. On some models you hold Start for about 3 seconds to unlock the controls.
- When to call Aria
- If Bake stays cold, or the oven shows F3 E1, book a visit. We test the element, igniter and sensor before replacing anything.
Smooth-Top Element Not Heating
- Likely cause
- A failed element, its infinite switch, or a control fault on touch-control models.
- Try this first
- Try the same pot on another element at the same setting to see if it's one element or the whole cooktop. On FlexHeat dual elements, check you've selected the size you want.
- When to call Aria
- If one element stays dark or won't turn off, book a visit. We test the element and switch first.
Gas Burner Clicks but Won't Light
- Likely cause
- Usually a wet or misaligned burner cap, or a weak igniter.
- Try this first
- Once the cooktop is cool, dry the burner cap and base and seat the cap flat.
- When to call Aria
- If it still won't light, we test the igniter and spark module. If you smell gas, leave it off and call your gas utility first.
Oven Shuts Off or Shows an F Code
- Likely cause
- A sensor, door lock or control fault, or a keypad issue. On many models F2 E1 points to the keypad or its wiring.
- Try this first
- Turn the stove off at the breaker for one minute, then try again. Check the cooktop grates are seated level, since a bumped grate can press a key.
- When to call Aria
- If the code comes back, write it down and book a visit.
Good to know
Whirlpool wall ovens and cooktops get the same approach: we test the element, igniter, sensor and controls before replacing anything.
Most stove and oven repairs we do land around $130–$350, depending on the part. You get the exact price before any work starts.
RelatedStove and oven repair · Oven not heating guide · Oven repair cost
Whirlpool Washer Problems We Fix
We repair Whirlpool front-load washers and top-load washers, including 2-in-1 removable agitator models.
Washer Leaking
- Likely cause
- On front-loaders, a torn door boot seal, a loose drain pump filter cap or a split internal hose. On top-loaders, often a hose, the pump or the tub seal.
- Try this first
- Check the drain pump filter cap (front-loaders) is screwed in tight, and look at the fill hoses at the back for drips. Use HE detergent and a little less of it, since too much suds can push water out.
- When to call Aria
- If water still shows up after a normal load, book a visit. Tell us where the puddle starts, front or back.
Not Draining (F9 E1)
- Likely cause
- A clogged drain pump filter, a kinked drain hose, or a pump that has failed.
- Try this first
- On front-loaders, put towels and a shallow tray down, then open the small access door at the bottom front and clean the drain pump filter. Check the drain hose isn't kinked or pushed too far into the standpipe.
- When to call Aria
- If F9 E1 keeps coming back, the drain pump needs testing.
Not Filling (F8 E1)
- Likely cause
- Closed or partly closed taps, kinked fill hoses, clogged inlet screens, or a failed water inlet valve.
- Try this first
- Open both the hot and cold taps all the way and straighten the hoses. Whirlpool doesn't recommend anti-flood devices on the hoses, since they can slow the fill.
- When to call Aria
- If F8 E1 shows up with both taps fully open, book a visit.
Door or Lid Won't Lock (F5 E2)
- Likely cause
- Something caught in the door, a worn latch, or a failed door lock.
- Try this first
- Check nothing is caught in the door or lid and close it firmly. Press Pause/Cancel twice and Power once to clear the code, then restart.
- When to call Aria
- A worn door lock is a common repair. If the code returns, book a visit.
Good to know
Leave the door open between loads and run the Clean Washer cycle about once a month. It keeps smells and drain codes down.
Most washer repairs we do land around $150–$350, depending on the part. You get the exact price before any work starts.
RelatedWasher repair
Whirlpool Dryer Problems We Fix
We repair Whirlpool electric and gas dryers, including stacked units and steam models.
Check Vent Light or Taking Too Long
- Likely cause
- Restricted airflow, usually lint in the vent duct or a crushed or stuck outside flap. Whirlpool's Check Vent alert is a warning about the vent, not a dryer fault.
- Try this first
- Clean the lint screen, then check the duct behind the dryer isn't crushed or kinked and the outside flap opens when the dryer runs. Short, straight 4-inch metal duct works best.
- When to call Aria
- If the vent is clear and loads still take more than one cycle, book a visit. We check the heating parts and the sensors.
Dryer Not Heating
- Likely cause
- On electric dryers, often a heating element or thermal fuse. On gas dryers, an igniter or gas valve coils. A blown thermal fuse usually means the vent was blocked.
- Try this first
- Check both breakers for an electric dryer, since one can trip and leave the drum turning with no heat. On gas dryers, check the gas valve behind the dryer is open.
- When to call Aria
- We test and replace the failed part, and check the vent so it doesn't happen again.
Drum Not Turning or Thumping
- Likely cause
- A broken drive belt, worn drum rollers or idler pulley, or a failed motor.
- Try this first
- Check nothing heavy like a shoe or a sock has wedged at the front of the drum, and that the door switch clicks when you close the door.
- When to call Aria
- If the drum won't turn, or it thumps or squeals, stop using it and book a visit.
Code on the Display (F3 E1 or F3 E2)
- Likely cause
- F3 E1 points to the exhaust thermistor and F3 E2 to the moisture sensor, which tells the dryer when clothes are dry.
- Try this first
- Turn the dryer off at the breaker for one minute. For F3 E2, make sure the dryer is level and try a larger load, since small loads may not touch the sensor bars.
- When to call Aria
- If the code comes back, we test the sensor and its wiring.
Good to know
Stacked and laundry-closet dryers: the duct connection is hard to see, so check it wasn't crushed when the dryer was pushed back.
Most dryer repairs we do land around $130–$320, depending on the part. You get the exact price before any work starts.
RelatedDryer taking too long · Dryer repair
Whirlpool Dishwasher Problems We Fix
We repair Whirlpool built-in dishwashers, including top-control and front-control models with a third rack.
Not Draining (F9 E1)
- Likely cause
- A clogged filter, a kinked drain hose, a new disposal's knockout plug, or a drain pump that has failed.
- Try this first
- Twist out and rinse the filter in the bottom of the tub, check the drain hose under the sink for kinks, and run the disposal before you start a cycle.
- When to call Aria
- If water still sits in the bottom, the drain pump needs testing.
Dishes Not Getting Clean
- Likely cause
- A dirty filter, blocked spray arms, low water temperature, or a wash pump that's weak.
- Try this first
- Clean the filter about once a month, check the spray arms spin freely, and run the kitchen tap until it's hot before starting.
- When to call Aria
- If dishes still come out gritty with a clean filter, book a visit.
Water Under the Dishwasher (F8 E4)
- Likely cause
- Water has reached the base pan, from a loose fill line, a door gasket or too much suds.
- Try this first
- Use only dishwasher detergent, never dish soap. Check the door closes evenly and nothing is caught on the gasket.
- When to call Aria
- Switch it off and book a check, since the source of the water needs finding.
Not Drying
- Likely cause
- Plastics that don't hold heat, an empty rinse aid dispenser, or a failed heating element or vent on heated-dry models.
- Try this first
- Top up the rinse aid and use the heated-dry or extra-dry option if your model has it.
- When to call Aria
- If metal and glass dishes come out wet too, the heating element or the vent needs testing.
Good to know
Whirlpool filters twist out by hand, so rinsing them once a month prevents many drain and cleaning problems.
Most dishwasher repairs we do land around $130–$340, depending on the part. You get the exact price before any work starts.
Whirlpool Microwave and Range Hood Problems We Fix
We repair Whirlpool over-the-range microwaves, including low-profile microwave hood combinations, and Whirlpool range hoods.
Vent Not Clearing Smoke
- Likely cause
- Grease filters clogged under the microwave or hood, a stuck damper, or an old charcoal filter on a recirculating setup.
- Try this first
- Pull out the metal grease filters and soak them in hot soapy water. Replace the charcoal filter if your microwave or hood recirculates.
- When to call Aria
- If the fan sounds weak with clean filters, book a visit to check the motor and damper.
Microwave Runs but Doesn't Heat
- Likely cause
- A failed high-voltage diode, capacitor, magnetron or door switch.
- Try this first
- Make sure the door closes firmly and try heating a cup of water for one minute. If the light, fan and turntable work but the water stays cold, stop using it.
- When to call Aria
- Microwaves hold a charge even when unplugged, so please don't open the cover. Book a visit and we test it safely.
Microwave Dead or Display Blank
- Likely cause
- A tripped breaker, a blown internal fuse, or a door switch that has failed.
- Try this first
- Check the breaker and try resetting it once.
- When to call Aria
- If it's still dead, a door switch is often the cause, and we test it before replacing anything.
Vent Fan or Light Not Working
- Likely cause
- A failed fan motor, a blown bulb or LED, or the control board.
- Try this first
- Clean or replace the grease filters under the microwave or hood, and try the fan on every speed.
- When to call Aria
- If the fan stays silent or the light won't come on with a new bulb, book a visit.
Good to know
Microwaves can hold a charge after unplugging, so please don't open the housing yourself. We test them safely.
RelatedMicrowave repair · Range hood repair
Whirlpool Error Codes by Appliance
Codes vary by model, so treat this as a guide for many models, not every one.
Whirlpool Fridge Codes
See fridge problemsF# E#System fault (flashing F)
On models with a display, any flashing F or F-and-E code means the fridge found a fault.
What to try
Unplug it or turn off the breaker for one minute, then check cooling is turned on.
When to call
If the code comes back, write it down and book a visit.
COOLING OFFCooling is turned off
On models with a display. It can get switched off during cleaning.
What to try
Turn cooling back on. On many models, hold LOCK and MEASURED FILL together for 3 seconds.
When to call
If cooling is on and it still isn't cold, book a visit.
Temperature AlarmFridge or freezer too warm
Sounds when the fridge is above 9 °C (48 °F) or the freezer above −9 °C (15 °F) for over 1½ hours.
What to try
Keep the doors closed and give it a few hours to recover.
When to call
If it doesn't cool back down, book a visit.
Door AjarA door is open
The alarm repeats every 2 minutes until the door is closed.
What to try
Close all doors and check bins or food aren't in the way. Check the fridge is level.
When to call
If the doors are closed and it stays on, the door switch needs testing.
H2OWater filter is due
The filter status light. Replace the filter about every 6 months.
What to try
Replace the filter. On many models, hold LIGHT and ICE TYPE for 3 seconds to reset the light.
When to call
If the light won't reset, book a check.
Whirlpool Stove and Oven Codes
See stove and oven problemsF3 E1Oven temperature sensor problem
Shown as F3 E0 on some models.
What to try
Turn it off at the breaker for one minute, then try again.
When to call
If it returns, the sensor and wiring need testing.
F2 E1Keypad or control problem
Shown as F2 E0 on some models.
What to try
Make sure the cooktop grates sit level, then reset the breaker for one minute.
When to call
If it comes back, the keypad or control needs a technician.
F1 E1Oven control problem
What to try
Turn it off at the breaker for one minute, then try again.
When to call
If it returns, the control or its wiring needs testing.
F5 E1 / F5 E2Door latch or door switch problem
Often after a self-clean.
What to try
Let the oven cool, then reset the breaker for one minute.
When to call
If the door won't lock or unlock, book a visit.
Whirlpool Washer Codes
See washer problemsF9 E1Taking too long to drain
What to try
Clean the drain pump filter (front-loaders) and check the drain hose for kinks.
When to call
Still F9 E1? The drain pump needs testing.
F8 E1Not enough water coming in
Also shown as LO FL or LF on some models.
What to try
Open both taps fully and straighten the fill hoses.
When to call
If the taps are open, the inlet valve may have failed.
F5 E2Door not locking
Front-load models.
What to try
Check nothing is caught in the door and close it firmly.
When to call
A worn door lock is a common repair.
LdLLid not locking
Top-load models.
What to try
Check nothing is sticking up under the lid, then close it.
When to call
If the lid still won't lock, the lid lock needs testing.
F7 E1Motor speed problem
Front-load models. The drum can't reach the right speed.
What to try
Don't overload it. On a new washer, check the shipping bolts were removed.
When to call
If it returns, we test the motor and its control.
Sud / SdToo many suds
The washer adds extra rinses to clear them.
What to try
Use HE detergent and less of it.
When to call
If suds keep coming back with HE detergent, book a check.
Whirlpool Dryer Codes
See dryer problemsCheck VentRestricted airflow
Shown as a light or as AF on some models. A blocked vent is a fire risk.
What to try
Clean the lint screen, the duct and the outside flap.
When to call
If the vent is clear and the alert stays on, book a visit.
F3 E1Exhaust thermistor problem
What to try
Reset the breaker for one minute and run a timed dry.
When to call
If it returns, we test the thermistor.
F3 E2Moisture sensor problem
What to try
Level the dryer and try a larger load.
When to call
If it returns, the sensor or its wiring needs testing.
L2Low or no power to the heater
Electric models. The drum turns but there is little or no heat.
What to try
Check both dryer breakers are on, or reset them.
When to call
If the breakers are fine, the power supply or heater circuit needs testing.
F2 E1Stuck keypad button
What to try
Turn it off at the breaker for one minute, then try again.
When to call
If it comes back, the keypad needs a technician.
PFPower was interrupted
What to try
Press and hold Start to restart, or press Power to clear it.
When to call
If it keeps showing without a power outage, book a visit.
Whirlpool Dishwasher Codes
See dishwasher problemsF9 E1Taking too long to drain
What to try
Clean the filter, check the drain hose and the disposal knockout plug.
When to call
If it still won't drain, the pump needs testing.
F8 E4Water in the base pan
The dishwasher has detected water underneath.
What to try
Use only dishwasher detergent, never dish soap.
When to call
Turn off the water to it and book a check.
H2ONot detecting water
What to try
Check the water supply valve under the sink is open and the hose isn't kinked.
When to call
If water is on, the inlet valve may have failed.
F8 E2Water inlet valve problem
What to try
Unplug it or turn off the breaker for 30 seconds.
When to call
If it returns, the inlet valve needs testing.
F9 E2Drain pump problem
What to try
Check the drain hose and the disposal, then reset the power.
When to call
If it returns, the drain pump needs testing.
F7 E2Wash motor problem
What to try
Unplug it or turn off the breaker for 30 seconds.
When to call
If it comes back, the wash motor needs a technician.
Whirlpool Microwave Codes
See microwave problemsF2Keypad problem
Over-the-range models.
What to try
Turn it off at the breaker for one minute, then try again.
When to call
If it comes back, the keypad or wiring needs testing.
SEKeypad problem
Over-the-range models.
What to try
Turn it off at the breaker for one minute, then try again.
When to call
If it comes back, the keypad or wiring needs testing.
F3HHumidity sensor problem
Over-the-range models.
What to try
Turn it off at the breaker for one minute, then try again.
When to call
If it returns, the sensor needs testing.
F1E1Control board problem
Over-the-range models.
What to try
Turn it off at the breaker for one minute, then try again.
When to call
If it returns, the control board or wiring needs testing.
DoorDoor message
The door was closed for 5 minutes without starting.
What to try
Open and close the door firmly, then start again.
When to call
If it won't clear, the door switches need testing.
Code still showing after the quick checks? Tell us the code when you book.
Typical Whirlpool Repairs
Typical Whirlpool repairs we see, and what usually fixes them. See our recent jobs on Our Work.
Typical Whirlpool repair
Whirlpool Front-Load Washer: F9 E1 Code
Most F9 E1 calls come down to a clogged drain pump filter or a pump that has stopped. We clean the filter and test the pump, and replace it only if it has failed.
Washer repairTypical Whirlpool repair
Whirlpool Dryer: Check Vent and Long Dry Times
A blocked or crushed vent makes the dryer run long and can blow the thermal fuse. We clear the airflow problem first, then test the heating parts and replace what has failed.
Dryer repairTypical Whirlpool repair
Whirlpool Dishwasher: Not Draining
Usually a clogged filter or a blocked drain hose, and sometimes the drain pump itself. We clear the blockage and test the pump before replacing anything.
Dishwasher repairWhirlpool Repair Pricing
Current offers on diagnostics and installation. You always get the price before work begins.
Diagnostic regularly $129, now $99
$99
Your technician diagnoses your Whirlpool and gives you the price before any work begins. Diagnostic regularly $129, now $99, and always waived when Aria does the repair.
Installation From $129
From$129
A new Whirlpool washer, dryer, dishwasher, stove or microwave installed from $129. Pricing depends on the appliance and the existing connections. See installation.
Payment
- Card
- Debit
- Cash
- PayPal
- Apple Pay
* Offers subject to change; price confirmed before work begins.
What Happens at the Visit
Book online or call us. We’ll confirm your appointment, diagnose the problem, and provide the repair price before any work begins.
- Step 01
Book Your Appointment
Call or book online and tell us which appliance needs service and what problem you’re experiencing.
- Step 02
We Diagnose the Problem
A technician inspects the appliance to find the cause of the problem.
- Step 03
You Approve the Repair
We explain the recommended repair and pricing before any work begins.
- Step 04
Repair & Testing
The approved repair is completed and the appliance is tested before we finish.
What to Tell Us When You Book
That helps us bring the right part and finish on the first visit more often.
The code
Exactly as shown, like F9 E1 F8 E1 Check Vent
The model number
- Washers & dryers inside the door frame or under the lid
- Fridges on the inside wall or ceiling of the fresh-food section
What you've tried
Like cleaning a filter or power-cycling the unit.
When it happens
At the startMid-cycleAt the end
Repair or Replace Your Whirlpool?
A simple rule of thumb, then the factors that change it. More on this: repair or replace your appliance.
Repair cost as a share of a comparable new Whirlpool
Under about halfand the rest in good shape: repair it.
Over about half, or other problems building upIt's a bigger decision. We give you the price so you can weigh it up.
Age & condition
An older appliance with several problems is a different call from a reliable one with a single failure.
Type of failure
Most Whirlpool repairs we see are a single part: a drain pump, a door lock, a heating element, a thermal fuse, a fan or an igniter.
The big-ticket parts
Compressor or sealed-system work on an older fridge, or a main control board on an older washer or stove.
The price, first
We give you the price first, so you can decide with real numbers.
On Whirlpool dryers, a heating element, thermal fuse or belt is almost always worth fixing, even on an older unit. If replacing makes more sense, we also do installation from $129.
What Homeowners Say About Aria
Leave a Google ReviewReal reviews from Vaughan homeowners on Google.
Where We Work
Whirlpool repair in every part of Vaughan, including Woodbridge, Thornhill, Maple, Kleinburg and Concord. Not in Vaughan? Yes, we may still be able to help. Call 1-888-642-0352 to confirm. See recent jobs on Our Work.
Service areaVaughanVaughan, Ontario
- Woodbridge
- Maple
- Concord
- Kleinburg
- Thornhill
- Vellore Village
- Sonoma Heights
- Patterson
- Elder Mills
- Vaughan Metropolitan Centre
- Carrville
- Islington Woods
Call 1-888-642-0352Mon–Sun 8 AM–10 PM
Book OnlineWhirlpool is a trademark of its owner. Aria Appliance Repair is independent and not affiliated with Whirlpool.
What does F9 E1 mean on my Whirlpool washer?
On many models, F9 E1 means the washer is taking too long to drain. Turn it off, put towels and a shallow tray down, and clean the drain pump filter behind the small door at the bottom front. Check that the drain hose isn't kinked or pushed too far into the standpipe. If F9 E1 keeps coming back, the drain pump needs testing.
What do F8 E1 and F5 E2 mean on a Whirlpool washer?
On many models, F8 E1 means the washer isn't getting enough water, so open both taps fully and check the hoses for kinks. F5 E2 means the door or lid isn't locking, so check nothing is caught and close it firmly. Press Pause/Cancel twice and Power once to clear the code. If either keeps coming back, book a visit.
Why is my Whirlpool washer leaking?
On front-loaders, the usual causes are a torn door boot seal, a loose drain pump filter cap or a split internal hose. On top-loaders, it's often a hose, the pump or the tub seal. Too much detergent can also push suds out. Tell us where the puddle starts when you book, because it helps us plan the visit.
What does the Check Vent light mean on my Whirlpool dryer?
It means the dryer is sensing restricted airflow, usually lint in the vent duct or a crushed duct behind the dryer. It's a warning about the vent, not a dryer fault. Clean the lint screen, check the duct and make sure the outside flap opens. If the vent is long or hard to reach, a vent cleaning company is the right call.
Why is my Whirlpool dryer not heating?
On electric dryers, it's often a heating element or thermal fuse, and on gas dryers an igniter or gas valve coils. First check both breakers on an electric dryer, since one can trip and leave the drum turning with no heat. A blown thermal fuse usually means the vent was blocked, so we check the vent as part of the repair.
What do F3 E1 and F2 E1 mean on a Whirlpool stove?
On many models, F3 E1 points to the oven temperature sensor or its wiring, and F2 E1 to the keypad or control. Turn the stove off at the breaker for one minute and try again. For F2 E1, check the cooktop grates are seated level. If either code comes back, write it down and book a visit.
Why is my Whirlpool fridge warm but the freezer is cold?
Usually the evaporator fan has stopped, or frost from a defrost fault is blocking the air that cools the fridge side. Make sure food isn't blocking the vents and the doors close fully. If the fridge stays above 4 °C after a day, book a visit. We fix the defrost cause, not just the ice.
What does F9 E1 mean on a Whirlpool dishwasher?
On many models, F9 E1 means the dishwasher is taking too long to drain. Twist out and rinse the filter, check the drain hose under the sink for kinks, and make sure a new disposal's knockout plug was removed. If water still sits in the bottom, the drain pump needs testing.
Is it worth repairing a Whirlpool appliance?
Most Whirlpool repairs are a single part: a drain pump, a door lock, a heating element, a fuse, a fan or an igniter, and those are usually worth fixing. A simple rule: if the repair costs less than about half of a comparable new appliance, repair it. The bigger calls are sealed-system fridge work or a main control board. We price it first, so you decide.
How much does Whirlpool repair cost?
Diagnostic regularly $129, now $99, and always waived when Aria does the repair. After testing, you get the exact repair price before any work starts. Installing a new Whirlpool appliance starts from $129. We accept cards, debit, cash, PayPal and Apple Pay, and completed repairs carry our 1-Year Parts & Labour Warranty.
Can you get parts for my Whirlpool washer or dryer?
Our technician pins down the exact Whirlpool part and gives you the repair price before any work. If a part needs ordering, such as a control board, we tell you the timing up front and book a second visit that suits you. Keep your model number handy. On Whirlpool washers, it's usually inside the door frame or under the lid.
How do I book Whirlpool repair near me?
Book online by choosing your appliance, a day and an arrival window, or call 1-888-642-0352, Mon–Sun 8 AM–10 PM. We serve all of Vaughan, including Woodbridge, Maple, Kleinburg, Concord and Thornhill. If you're outside Vaughan, call to confirm your address. Write down any code on the display first, because it helps us plan the visit.
Need Appliance Repair or Installation?
Tell us which appliance you need repaired or installed and we’ll help arrange your appointment.
- Same-Day Service Available
- 1-Year Parts & Labour Warranty
- Mon–Sun 8 AM–10 PM
